Sarvadnya Engineering Institute

• Introduction on Oil and Gas industry, Chemical plants, Petroleum and utility sectors and Roles and responsibility of Piping Engineer in various industry. Introduction on other departments in EPC Sector.
• Introduction on Piping design system, Definition of pipes, valves, fittings, special parts, mechanical equipment. Types of pipes, fittings, valves, special parts etc. Introduction of Codes and Standards for Piping system, ASME B31.3
• Introduction of mechanical equipment like Pumps, Heat exchanger, Compressor, Distillation column, Chiller, Cooling tower, Boiler, Turbine, Pressure vessel, Tanks, Heater, Reactors, Agitators, Hydro-pneumatic system.
• Introduction of: - PFD/PID, Equipment layout, Nozzle orientation, Piping layout, Isometric, Fabrication drawing, Piping support drawing, GA Drawing, Pipe rack.
• Introduction of materials for Pipes, fittings, valves, special parts, plate etc. ASTM table, Valve datasheet, Piping Material Specification (PMS), Special parts datasheet, RF Pad calculation, Mitre bend calculation, Pipe Wall thickness calculation. Material selection criteria for piping system.
• Detail Design Engineering of Plot plan development as per OISD 118
• Detail Design Engineering of Pipe rack Design (Process and Utility)
• Detail Design Engineering of Tank farm as per OISD-118, Introduction of petroleum products (Class A/B/C and excluded)
• Detail Design Engineering of distillation column and its various equipments.
• Preparation of Piping MTO / BOQ at various stages (30%, 60%, 90%)
• Preparation of piping layout for Pump suction / Discharge lines, Isometric and BOQ for the same. Preparation of nozzle orientation drawing for Horizontal / Vertical vessels / Tanks.
• Introduction of Piping supports:- Primary and Secondary for critical and Non critical piping systems. Introduction of piping insulation and Heat tracing.
• Introduction of stress analysis and Ceaser-II
• Overview of PDMS software
• Personality development and mock interview, Communication skills and Final exam

  PDMS software 

• Introduction to PDMS
• Modules
• Equipment Application
• Piping Application
• Structure Application
• Cable Tray Application
• HVAC Application
• Iso Draft
• Draft
• Appendix

CEASER-II SOFTWARE 

Statics Subjects Covered

• Introduction
• Nozzle Thermal Growth Calculations – pumps, vessels, heat exchangers.
• Modeling of Piping elements & isometrics – Bends, Reducers, Valves, Loops
• Performing Static Analysis.
• Modifying Load Cases.
• Hanger Selection
• Set up of Wind Load Cases.
• Set up of SUS, OPE, EXP, HYD, HGR, OCC loads.
• Load Case Editor
• Viewing Reports
• Equipment Nozzle Load Qualifications
• Coding technique of Vessel Piping includes both piping and vessel coding in Caesar II.
• Local vessel flexibilities
• Evaluation of local vessel stresses
• Practical Examples – Input, Analysis & Redesign.

Dynamics Subjects Covered

• Building a dynamic analysis model.
• Interpreting dynamic analysis results.
• Evaluating transient loads with time history analysis.
• A survey of approaches to evaluating relief valve discharge.
• Solving field vibration problems using harmonic analysis.
• Seismic analysis using the response spectrum method.

• Introduction and Overview of:
• Role of Process Equipment designer in various fields, Industry functioning and plot overview, Basic process requirement of plants/projects Importance of codes and standards and their applications.
• Various Documents study:
• P&ID, Process Data Sheet, PFD and other documents used for designing, Vendor data, its checking & use in design other various inputs. Vendor fabrication drawings, Bill of material (BOM)
• Selection of materials required for various services To understand pressure part calculations
• Preparation of: Mechanical data sheets of process equipment, Bill of Material at various stages
• Basic Introduction of: Piping components used in equipment, Construction procedure of process equipment, Welding, Inspection and method of testing.
• Mechanical design of Process Equipment (Vessels, Reactors, Heat Exchanger, Distillation Columns etc.)
• Overview of Accessories mounted on equipment 
• Overview of Chimney Design as per IBR code
• Overview of Equipment Design Software like PV Elite
• Overview of NDT Tests and application
• Overview of Rotary Equipment and its application
• Overview of Piping system
• Overview of ASME SEC VIII, Div-1, Div-2, Div-3
• Overview of TEMA standard 
• Overview of API 650 &IS 803

Overview of:

• Plumbing System Fundamentals 
• Introduction to Plumbing System. 
• Plumbing Codes & Standards. 
• Plumbing Fixtures  Bathroom & Toilet Fixtures , Kitchen Fixtures ,general fixtures
• Piping Systems in plumbing & firefighting
• Pipe Fittings in plumbing & firefighting 
• Valves in plumbing & firefighting
• Piping / Plumbing Isometrics
• Piping Supports types, Selection & spans
• Portable Pump Sizing in plumbing & firefighting
• Parts of Drainage System in plumbing & firefighting
• Drainage Fittings in plumbing & firefighting
• Types of Vent Pipes in plumbing & firefighting
• Fire Protection Systems in plumbing & firefighting
• Codes & Standards of Fire Protection NFPA Codes  
• Water based Fire Protection system. - Building occupancy  Classification 

PLUMBING & FIRE-FIGHTING Designing system 

• Design of Cold & Potable Water Systems in plumbing & firefighting
• Design of Hot Water Plumbing System in plumbing & firefighting
• Design & Layout of Drainage System in plumbing & firefighting
• Estimation of minimum number of Plumbing Fixtures for facilities  
• Estimation of Water Demand (Hot & Cold Water) using R.B Hunter
• Curves For Residential & Non- Residential applications in plumbing & firefighting
• Fire Sprinkler System in plumbing & firefighting
• System Design in plumbing & firefighting
• Preparation of Sprinkler layout / Sprinkler Riser Drawings in plumbing & firefighting.
• Water supply connection to Wet pipe sprinkler system in plumbing & firefighting.

Post Designing of PLUMBING & FIREFIGHTING Engineering

• Checking Vendor Data in plumbing & firefighting
• Drafting of Plumbing Systems. 
• Abbreviations & Symbols used in plumbing & firefighting
• Raw/Grey overhead & underground tank sizing with pump selection
• Commissioning evaluation of  PLUMBING & FIREFIGHTING system
• Test Operation on commissioning in plumbing & firefighting
• Monitoring Parameters, Performance test for PLUMBING & FIREFIGHTING Engineering.
• Arrangement of Dry & Wet riser in plumbing & firefighting
• PLUMBING & FIREFIGHTING engineering Software’s
• Revit MEP in plumbing & firefighting

Training on Live Projects for PLUMBING & FIREFIGHTING Engineering   

System planning

• Basic design considerations
• Planning guide for the supply and distribution system
• Power system modernization and evaluation studies/programs
• Voltage considerations
• Voltage control in electric power systems
• Voltage selection
• Voltage ratings for low-voltage utilization equipment
• Voltage drop considerations in locating the low-voltage/ high-voltage
• Calculation of voltage drops 
• Preparing the cost estimate
• Different entities of illuminating systems
• Light sources: daylight, incandescent, electric discharge, fluorescent, arc lamp and Lasers
• Prepare layout of Different type lights
• Cable Sizing and Selection of single Phase and Three Phase
• Internal Electrification design
• PROTECTION OF BUILDINGS AND ALLIED STRUCTURES AGAINST LIGHTNING
• Earthing Design and Calculation of Power Plants
• DESIGN AND ENGINEERING OF TRANSMISSION LINE
• DESIGN AND ENGINEERING OF SWITCHYARD